Trunk, Wheel Well, Fender Liners

[aguirola]

Hello Drew,

If you can send a photo or two, that would be great, as if there are too many cracks and patches to be made,
they will telegraph on the mould.

Let's try the easy way first:

alberto.guirola at gmail dot com

Regards, Alberto

 

[3moons]

Hello Drew,

If you can send a photo or two, that would be great, as if there are too many cracks and patches to be made,
they will telegraph on the mould.

Let's try the easy way first:

alberto.guirola at gmail dot com

Regards, Alberto

Left:

Foam lining:

Thickness:

- S

 

[3moons]

-

 

[afeustel]

The pics that 3moons sent show one in much better condition than mine.

 

[Frederick]

3moons look completely intact, good examples. they will likely always have some cracks. Easy to fix with fiberglass cloth and a good 2 part, sandable epoxy. Makes them sturdy as well.

 

[aguirola]

Well, we pulled the stops and are starting the mould making on the Coupe trunk wheel covers.
Hopefully there will some takers
If not I'll have a set of spares...

Will post developments.

Regards, Alberto

 

[aguirola]

Hello Drew,
Your trunk liners look very good, if you would like to mail them to me I would be more than pleased
to undertake this project also, alongside the E9 units, and hopefully, we get some show of hands.
If you would like to proceed, I will make a mould of your liners. The foam aspect will have to be discussed.

Regardless, if you volunteer the initial parts, you will receive in return your originals + a free set.

Please pm if you would care to continue on this project.

Regards, Alberto

 

[bavbob]

I would be in for a set!

 

[aguirola]

Thank you Bob! We need to make at least 6 or 7 sets, probably...

Regards, Alberto

 

[aguirola]

Photos of my trunk liners.
I found there are the 2 large ones and 2 smaller, 1/2 moon.
Is the 1/2 moon of interest, or only the large ones?

Regards, Alberto

 

[bavbob]

I would say both for originality.

 

[mmccusername]

I would say if you're going to make any of the trunk pieces, you need to make them all. Otherwise they will not match.

 

[afeustel]

Hello Drew,
Your trunk liners look very good, if you would like to mail them to me I would be more than pleased
to undertake this project also, alongside the E9 units, and hopefully, we get some show of hands.
If you would like to proceed, I will make a mould of your liners. The foam aspect will have to be discussed.

Regardless, if you volunteer the initial parts, you will receive in return your originals + a free set.

Please pm if you would care to continue on this project.

Regards, Alberto

Hello Alberto.

I am happy to send my pieces but the ones pictured above are from @3moons. I think if we want a good set, then we need @3moons to send them as mine have many cracks. If it does not look like there are any alternatives in a week or so, I will box mine up and send them your way.

Regards,
Drew

 

[Drew Gregg]

I need just the half-circle liners for my E9 that go next to the fenders. I bought the wheel well liners from W&N some time ago.
Please let me know if you are making them. Thanks, Drew

 

[aguirola]

Drew, yes, I am making the half moons also.

On this issue, duly noted, that is my opinion also, a full set ought to be the solution,
except if you only want the 1/2 moons, we aim to please.
Thank you for the feedback.

Regards, Alberto

 

[HB Chris]

Even though this is an E3 Thread, we are talking e9, correct?

 

[aguirola]

Chris, yes, you are right! Kind of deviated on the model, yet more or less same part

Regards, Alberto

 

[3moons]

Apologies to Aguirola and Afeustel for stepping into your communication.
Without my reading glasses, I reopened this thread after taking pictures and intended to reply to post #3 but mistakenly replied to post #21.
That said, I’m happy to volunteer my wheel well trunk liners for the project.

Aguirola, I’ll respond to your PM.

Here’s the right side liner:

- S

 

[aguirola]

I am posting examples of the first moulds for the E9.
I think they came out great. The heat distorted the original half moons, so I will install the new ones.
They were really flimsy cheap vacuformed junk,
Well, in the day, they really passed muster
Regards, Alberto

 

[Candia4441]

I am posting examples of the first moulds for the E9.
I think they came out great. The heat distorted the original half moons, so I will install the new ones.
They were really flimsy cheap vacuformed junk,
Well, in the day, they really passed muster
Regards, Alberto

View attachment 136589


View attachment 136590

View attachment 136591

Hello, I will buy a set for my E9 if it is for sale